COMPACT HIGH POWER LASER DAZZLER™ (CHPLD)

About This Presentation

Title:

COMPACT HIGH POWER LASER DAZZLER™ (CHPLD)

Description:

COMPACT HIGH POWER LASER DAZZLER (CHPLD) INITIAL TRAINING PRESENTATION TOPICS Introduction 3-7 Warnings/Safety 8-9 Specifications 10 Nomenclature 11 Battery ... – PowerPoint PPT presentation

Number of Views:336

Avg rating:3.0/5.0

Slides: 22

Provided by: laserdazz

Category:

more less

Transcript and Presenter's Notes

Title: COMPACT HIGH POWER LASER DAZZLER™ (CHPLD)

1
COMPACT HIGH POWERLASER DAZZLER(CHPLD)
INITIALTRAINING PRESENTATION
2
TOPICS

Introduction 3-7
Warnings/Safety 8-9
Specifications 10
Nomenclature 11
Battery Replacement 12
On-Off Push Button 13
Intermittent Button Switch 13
Remote Switch Tail Module 14
Make Safe When Not In Use 15
Delrin Fixture 16
Diffuser 17
Cleaning 18-19
Tips 20
Questions 21

3
CHP LASER DAZZLER
A Portable, Non-Lethal, Eye-Safe, Multi-Purpose
Device Effective Both Day and Night
4
CHP LASER DAZZLER

It is the most rugged/powerful/compact laser
device available that is suitable for this
purpose
The CHPLD engages the target in a wall of green
laser (532nm) light, which disorients and
distracts the subject
This is accomplished by overloading the optic
nerve rendering the subject nearly sightless for
a short period of time there is no doubt the
individual will see the CHPLD, even in bright
sunlight at 200 meters

5
CHP LASER DAZZLER

Specifically designed for applications where
gaining the instant attention of individuals in
varying light conditions including clear, bright
sunny days is critical
IDEAL FOR CONVOY AND ENTRY CONTROL OPERATIONS
Immediate recognition by approaching vehicles or
pedestrians which avoids the use of lethal force
due to confusion or unseen /unrecognized hand
signals

6
Drivers approaching a convoy or checkpoint may
not see hand signals or realize they are entering
a restricted/danger zone
CHPLD at 100 yards bright daylight
They cannot fail to see the CHPLD even if
distracted by traffic, sunlight, pedestrians, or
other activities
7

OTHER USES
Mark your position and identify friendly units at
long distances
Distraction disruption of hostile groups
Counter sniper
Block line of sight when approaching target
Counter surveillance

Mounted on Tripod
Front view showing 4 lasers
8
WARNINGS/SAFETY

Laser Dazzlers are non-lethal devices, HOWEVER,
with the potential for permanent eye damage if
used improperly the CHPLD should always be
TREATED LIKE A LOADED WEAPON
DO NOT point this device at any person unless it
is operationally required
The user is solely responsible for the safe
operation of the CHPLD and for adhering to the
instructions and warnings provided
DO NOT look at the CHPLD thru optical devices
such as binoculars or telescopes
This device has sufficient energy densities to
cause irreversible eye damage and or permanent
blindness if used on a subject at close distances
or reflected onto a subjects eyes from a highly
reflective surface

9
WARNINGS/SAFETY

DO NOT use on subjects at distances closer than
20 meters or reflect back on subjects at
distances equivalent to 20 meters or closer
without the holographic diffuser installed
DO NOT use on subjects at distances closer than 3
meters or reflect back on subjects at distances
equivalent to 3 meters or closer with the with
the holographic diffuser installed
The CHPLD is powered by lithium sulfur dioxide
primary batteries and are therefore NOT
RECHARGEABLE
DO NOT attempt to charge the battery pack. Any
attempt to do so is dangerous

10
SPECIFICATIONS

500 Milliwatt, 532nm (green) flashing laser
Overall length - 11 inches
Maximum diameter - 2.5 inches
Powered by lithium sulfur dioxide primary
batteries
BATTERIES ARE NOT RECHARGABLE
Safe Ranges
Minimum eye safe range 20 meters (Without
holographic diffuser)
Minimum eye safe range 3 meters (With
holographic diffuser)
Maximum effective range
200 meters bright sunlight
2 kilometers night
Construction
Anodized aluminum
Weight 2.0 lbs.
Weight as shown 2.6 lbs.
All parts produced in the USA
Operating Conditions
All-weather, general purpose and water tight

11
NOMENCLATURE
Aiming Device
DELRIN FIXTURE
CHPLD
12
BATTERY REPLACEMENT

Unscrew tail module
Install battery positive end first
Rotate battery for best fit when installing
Check to confirm O-Ring (3) is still in place
DO NOT over tighten switch module

13
ON-OFF PUSH BUTTON

Push and release to turn on
Push and release again to turn off

INTERMITTENT BUTTON SWITCH

Operate laser by push and release of intermittent
button switch

14
REMOTE SWITCH TAIL MODULE

This module contains an electronic switch circuit
powered by a capacitor which is charged by the
battery pack when the laser is OFF
INITIAL CHARGE REQUIRES 4 MINUTES

The laser can be operated for 45 minutes
continuously from the initial charge
When the laser is turned off the capacitor is
fully charged
The cable connectors for this module are
male/female pin type
Mate each connector
Secure by gently rotating the locking collar
until it engages the mating part
Rotate clockwise approximately 1/8 of a turn to
lock in place

15
MAKE SAFE WHEN NOT IN USE

Integral On-Off Push Button Switch Module
Unscrew ¼ to ½ turn
Press button to ensure laser does not fire
If necessary unscrew additional ¼ turn increments
until laser will not fire
Remote Switch Tail Module
Disconnect cable connectors
DO NOT unscrew module since the capacitor charge
may dissipate and the initial charge time (4
minutes) would be required to operate the laser
Press button switch to ensure laser does not fire
Long Period of Non-use
Remove battery pack
Reinstall Tail Switch Module to prevent dirt and
moisture from entering the device

16
DELRIN FIXTURE

The laser is provided in the Delrin Fixture and
sighted to the red dot reticule scope.
An intermittent on/off button is built into the
fixture and is armed by connecting the cable on
the Tail Module to the mating connector on the
Delrin Fixture
Secure by gently rotating the locking collar
until it engages the mating part
Rotate clockwise approximately 1/8 of a turn to
lock in place

17
DIFFUSER

Adding the provided Holographic Diffuser reduces
the minimum eye safety distance from 20 meters to
only 3 meters
Unscrew window module
Remove white washer
Place diffuser on window
Reinstall white nylon washer
Reinstall module on device

18
CLEANING

Remove the laser from the Delrin Fixture
Disconnect cable
Remove the Tail Module
Loosen the 6-32 set screws
Slide the laser forward
Make sure not to lose the O-Ring (3)
It is not necessary to remove the set screws
To reinstall just reverse the process

19
CLEANING

Window
With device front facing down unscrew window
module
Remove white nylon washer
Turn module over and clean surface underneath
The window O-Ring will drop out
Clean window with appropriate cleaner such as
Windex sprayed onto a cloth
Reinstall in reverse order
Make sure O-Ring (1) is in the groove
Make sure O-Ring (2) is still on the laser body
CHPLD
Wipe with damp cloth and or a cleaner such as
Windex sprayed onto the cloth
DO NOT immerse in water or cleaning fluids
NO OTHER FIELD DISASSEMBLY OF THE LASER OTHER
THAN AS DESCRIBED ABOVE IS PERMITTED. DOING SO
WILL DAMAGE THE DEVICE AND VOID THE WARRANTY

20
TIPS

TIPS FOR EFFECTIVE USE
Individuals or groups Aim at the center of the
chest then raise the beam to eye level for a very
short period of time repeat as necessary
Vehicles Aim at the center of the windshield
then move to the drivers side for a very short
period of time repeat as necessary

21
QUESTIONS ?
Easily seen at 1 mile in bright sunlight

Write a Comment

User Comments (0)