Laser%20Shoot-Out%20Game - PowerPoint PPT Presentation

About This Presentation
Title:

Laser%20Shoot-Out%20Game

Description:

Work almost complete on Weapon ... Using the serial interface. Moving on to Display Board and Central ... 1 Design and optimize laser receiver Code ... – PowerPoint PPT presentation

Number of Views:19
Avg rating:3.0/5.0
Slides: 20
Provided by: cegt201
Category:
Tags: 20game | 20shoot | laser | out | testing

less

Transcript and Presenter's Notes

Title: Laser%20Shoot-Out%20Game


1
Laser Shoot-Out Game
  • By Steven Noto and Laura Miller
  • Advisor Steven Gutschlag
  • April 4, 2000

Senior Project Status Report 2
2
Presentation Outline
  • Project Overview
  • Project Progress
  • Laser System Overview
  • Review of Completed Work
  • Software
  • Hardware
  • Schedule
  • Conclusion

3
Block Diagram

4
Project Progress
  • Work almost complete on Weapon hardware and
    software
  • Laser transmission and reception system has taken
    longer than expected

5
Laser Transmission System
6
Software Progress I
  • Weapon Software Objectives
  • Laser Interface
  • Serially send out data to be transmitted
  • Serially receive data from laser receiver
  • User Interface
  • Trigger, Reset, etc.
  • RF Interface

7
Software Progress II
  • Weapon Software Progress
  • Originally written in C and Assembly
  • Many problems integrating the two languages
  • Transferred to all C code
  • All assembly problems solved with only a small
    reduction in speed

8
Software Progress III
  • Weapon Software Status
  • User Interface
  • All buttons connected and tested
  • Laser Interface
  • Software components of transmission simulate
    correctly
  • RF Interface
  • Serial interface will be used instead

9
Future Software Milestones
  • Making sure the transmission software works with
    the hardware
  • Using the serial interface
  • Moving on to Display Board and Central Controller
    software

10
Weapon

11
Hardware Accomplishments
  • Reduced noise in laser receiver circuit
  • Added decoupling capacitors
  • Tried different oscilloscopes and different
    settings
  • Tried different feedback resistors

12
Hardware Accomplishments
  • Amplifier stage is operational
  • Designed and built
  • Problems with instabilities - Added Capacitors in
    parallel with feedback resistor
  • Problems with the first stage output voltage
    level saturating the second stage

13
Current Laser Receiver Output
14
Future Hardware Milestones
  • Laser receiver amplification
  • Change the gain on the current amplifier circuit
  • OOK detection circuit
  • Chip is already selected
  • OOK circuit
  • An oscillator and switch

15
Original Spring Schedule
  • Week Laura Steven
  • 1 Design and optimize laser receiver Code
    weapon software
  • 2 Design and optimize laser receiver Code
    weapon software
  • 3 Design and optimize laser receiver Code
    weapon - to - display Software
  • 4 Integrate laser receiver and weapon
    software
  • 5 Integrate laser receiver and weapon
    software
  • 6 Design C.C. electronics Code C.C. -
    to - display software
  • 7a Design display board electronics Code
    C.C. - to - display software
  • 7b Mid-term demonstration
  • 8 Design display board electronics
    Code C.C. - to - display software
  • 9 Design display board electronics
    Code display - to - user software
  • 10 Integrate C.C. hardware and software
  • 11 Integrate display hardware and
    software
  • 12 Integrate Subsystems
  • 13 Integrate Subsystems
  • 14 Presentation

16
Actual Spring Schedule
Week Laura Steven 1 Reviewed
Specs for Photo Diode, Learn to use Keil
PK51 Package Looked at Current to voltage
Converter 2 Set up simulation for I to V
converter Learn to use Keil PK51
Package 3 Finished simulations for both I to
Begin coding weapon software V converters
and started building circuits 4 Finish building
circuits and test them Interface weapon software
and laser systems
17
Actual Spring Schedule
Week Laura Steven 5 Trouble
shooting laser receiver Analyzing timing
for weapon software, circuit and noise
reduction running MMT test programs 6 Recorded
frequency response Coding and simulating
assembly of receiver circuit, worked on code
for laser interface noise problem 7 Started
amplifier design, Incorporating assembly and C,
finished testing receiver circuit running test
programs on MMT peripherals 8
Designed and built amplifier Incorporating
assembly and C circuit 9 Finished wiring
amplify circuits, Switching all weapon software
to C Fixed several problems with them code,
simulating weapon code
18
Conclusion
  • Software - Working on weapon software
  • Hardware - Working on laser receiver for the
    weapon
  • Many challenges to overcome to finish weapon

19
Questions?
Write a Comment
User Comments (0)
About PowerShow.com