ECET 405 Education for Service--tutorialrank.com

1
ECET 405 Education for Service--tutorialrank.com
2
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 1 Chapter 2 Homework For more
course tutorials visit www.tutorialrank.com   ECET
405 Week 1 Chapter 2 Homework
3
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 1 iLab For more course tutorials
visit www.tutorialrank.com   A Control Problem
with Multiple Inputs and Outputs 1.Complete Table
1 below per lab instructions 2.Take a digital
photo of your completed circuit and insert it
below. 3. In a paragraph write your comments on
any wiring issues or challenges that you
encountered. How did you troubleshoot or fix the
problem (if any)? Was there any flickering of the
LEDs when the motor was running or stopped? If
so, how would you fix the problem?
4
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 2 Chapter 2 Homework For more
course tutorials visit www.tutorialrank.com   Chap
ter 2 Homework 1)A discrete 120 V ac output
module is to be used to control a 230 V dc
solenoid valve. Draw a diagram showing how this
could be accomplished using an interposing
relay. 2)Assume a thermocouple generates a linear
voltage of from 20 mV to 50 mV when the
temperature changes from 750F to 1250F. How
much voltage will be generated when
5
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 2 iLab  For more course tutorials
visit www.tutorialrank.com   1.Per step 6 of Lab
2 instructions, turn on the power supply and
touch the loose end of the red wire shown in
Figure 7 to input terminals X0, X1, X2, X3, X4,
X5, X6, and X7. Indicate which of LEDs marked X0
to X7 will turn on. 1.Explain why some of the
input LEDs do not turn on as you touch the loose
red wire to some of the input terminals of the
PLC.
6
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 3 Chapter 4 Homework and Chapter
5 For more course tutorials visit www.tutorialrank
.com   ECET 405 Week 3 Chapter 4 Homework and
Chapter 5
7
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 3 iLab For more course tutorials
visit www.tutorialrank.com   1. Once you have
completed step 6 of lab 3, Print Screen your
ladder logic program that contains your last name
on rung 3 and paste it below. 2. Once you have
completed step 12 of lab3, Print-screen the
ladder logic program you created and paste it
below. Then submit the worksheet to week 3
Dropbox.
8
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 4 Chapter 7 Homework  For more
course tutorials visit www.tutorialrank.com   ECET
405 Week 3 Chapter 7 Homework
9
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 4 iLab Hardwiring your PLC For more
course tutorials visit www.tutorialrank.com   Hard
wiring your PLC, Downloading a Program Containing
Timer and Counter Instructions, and Running the
Process 1.Take a digital photo of your circuit
and attach to this worksheet 2. Print a copy of
the ladder logic program from your PC and attach
to this worksheet. 3. Briefly describe the
operation of each rung.
10
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 5 Homework For more course
tutorials visit www.tutorialrank.com   Chapter 10
- PP 298-300   Chapter 11 - PP
318-321   Chapter 13 PP 377-378
11
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 5 iLab Traffic Lights For more
course tutorials visit www.tutorialrank.com   Logi
xPro Simulation 1.Copy and paste the ladder
logic program you obtained in step 4 of the lab
to this worksheet. PLC Hardware 2.Take a digital
photo of your PLC wiring and attach to this
worksheet. 3.Print a copy of the ladder logic
program and attach to this worksheet.
12
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 6 Homework For more course
tutorials visit www.tutorialrank.com   Chapter 14
problems 1, 2, and 7 Chapter 15 problem 2 Chapter
14 Problem 1 Give an example of an open-loop
control system. Explain why the system is
open-loop, and identify the controller and final
control element.
13
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 6 iLab Project Design For more
course tutorials visit www.tutorialrank.com   ECET
405 Week 6 iLab Project Design
14
ECET 405 Education for Service--tutorialrank.com
ECET 405 Week 7 iLab Project Design II For more
course tutorials visit www.tutorialrank.com   1.Fi
ll in the values for voltages applied to the
motor and corresponding speeds from steps 6 and 7
in Table 1. 4.Write a brief report on the
functionality of your system. Describe any
troubleshooting or challenges you experienced
during the lab.
15
ECET 405 Education for Service--tutorialrank.com