REVOLUTION TUBE SETS - PowerPoint PPT Presentation

Loading...

PPT – REVOLUTION TUBE SETS PowerPoint presentation | free to download - id: 2d4b9-NWNiN



Loading


The Adobe Flash plugin is needed to view this content

Get the plugin now

View by Category
About This Presentation
Title:

REVOLUTION TUBE SETS

Description:

REVOLUTION Tubes have a different fit than our Classic Tubes. ... For guns like Perazzi's and Beretta's with spring loaded ejectors, drive tubes ... – PowerPoint PPT presentation

Number of Views:59
Avg rating:3.0/5.0
Slides: 17
Provided by: Ted9154
Learn more at: http://www.briley.com
Category:

less

Write a Comment
User Comments (0)
Transcript and Presenter's Notes

Title: REVOLUTION TUBE SETS


1
(No Transcript)
2
REVOLUTION TUBE SETS
  • Installation Removal Instructions

3
Installation
  • STOP !!!!!!
  • REVOLUTION Tubes have a different fit than our
    Classic Tubes.
  • READ ALL INSTRUCTIONS before beginning!!

4
Installation
  • REVOLUTION tubes should be fit semi-dry.
    Excessive oil will make fitting more difficult.
  • Clean the chamber and barrel prior to installing
    REVOLUTION tubes, using only a small amount of
    enclosed oil.
  • Lightly slide the first tube by hand all the way
    into the appropriate barrel until it stops.
  • Turning the tube, index the tube extractor to the
    gun extractor as shown next.

5
(No Transcript)
6
Insertion
  • Insert the appropriate aluminum driver into the
    chamber, small head first.
  • Using the soft-sided hammer, sharply strike the
    driver until the chamber seats.
  • REVOLUTION chambers are designed to fit tighter
    than the Classics and the benefit of tighter
    tolerances is that they should remain firmly in
    place from the first fit through the life of the
    barrel.

7
(No Transcript)
8
Note
  • Unlike Classics, REVOLUTION Revolution tubes do
    not fit up to a shoulder when installed.
  • They do require more hammer force to drive them
    in the first time. This initial fit settles into
    a comfortable fit after you do it a few times.
  • For Kreighoff, Browning and Blaser, as well as
    other guns that do not have spring loaded
    ejectors, the procedure is to use your
    appropriate driver to drive the tubes until the
    ejectors are flush with the receiver.
  • For guns like Perazzis and Berettas with spring
    loaded ejectors, drive tubes in until you notice
    the fit is fairly tight now check the muzzle end
    and verify that the tubes are almost flush with
    the end of your barrel.

9
Notice How the Tube is Flush with the Barrel
10
Driver Removal
  • Once the chamber is seated, you may need to
    wiggle the aluminum driver to remove it.
  • You may slap the side of the driver with the
    soft-sided hammer to help release it.
  • Assemble your gun.
  • If your gun does not close easily, you have not
    tapped the tubes in far enough.
  • See example next.

11
(No Transcript)
12
Tube Removal
  • When removing REVOLUTION, begin by disassembling
    your gun.
  • NOTE
  • Be sure to always leave both the barrel chokes in
    the barrel, and the tube choke in the tubes when
    extracting tubes.
  • Attempting to extract the tubes with tube chokes
    removed can damage both the tube choke threads
    and the tubes themselves.

13
Tube Extractor
  • To remove REVOLUTION tubes, insert the black tube
    extractor into the end of the barrel until it
    stops.
  • Sharply tap the black tube extractor with the
    soft-sided hammer.
  • Make sure the tube does not fall from the barrel
    when it is unseated.

14
(No Transcript)
15
Final Touches
  • Assemble your gun.
  • Does your gun open and close properly?
  • If it does not, then one or both of your tubes
    are not seated properly into the chamber deep
    enough. Proceed to correct the problem.
  • It would be a good idea to install your tubes in
    and out several times. Practice your new skills
    and get the learning over with. This new tube
    insertion becomes very easy after you do it a few
    times.

16
THANK YOU
  • for choosing Briley REVOLUTION Tubes.
  • They are the product of extensive research and
    experience, hand crafted in America with pride
    and the finest materials available. If you have
    any questions, please do not hesitate to call
    your sales rep. They will be happy to answer any
    questions you may have.
  • 800-331-5718
About PowerShow.com