To view this presentation, you'll need to enable Flash.

Show me how

After you enable Flash, refresh this webpage and the presentation should play.

Loading...

PPT – AC Fundamentals PowerPoint presentation | free to view - id: 11e443-OTNiO

The Adobe Flash plugin is needed to view this content

View by Category

Presentations

Products
Sold on our sister site CrystalGraphics.com

About This Presentation

Write a Comment

User Comments (0)

Transcript and Presenter's Notes

Lecture 4

- AC Fundamentals

Alternating Current

- Voltages of ac sources alternate in polarity and

vary in magnitude. - These voltages produce currents which vary in

magnitude and alternate in direction. - A sinusoidal ac waveform starts at zero,

increases to a positive maximum, decreases to

zero, changes polarity, increases to a negative

maximum, then returns to zero.

Sinusoidal waveforms

Generating AC Voltages

Generating AC Voltages

Coil voltage vs angular position

Current direction

Voltage and Current Conventions for AC

- Assign a reference polarity for the source.
- When the voltage e has a positive value, its

actual polarity is the same as the reference

polarity. - When e is negative, its actual polarity is

opposite that of the reference polarity. - When i has a positive value, its actual direction

is the same as the reference arrow. - If i is negative, its actual direction is

opposite that of the reference.

References for voltage and current

Frequency

- The number of cycles per second of a waveform is

called its frequency. - Frequency is denoted f.
- The unit of frequency is the hertz.
- 1 Hz 1 cycle per second

Period

- The period of a waveform is the duration of one

cycle. - It is measured in units of time.
- It is the inverse of frequency.
- T 1/f
- For 50 Hz T0.02 s

Amplitude and Peak-to-Peak Value

- The amplitude of a sine wave is the distance from

its average to its peak. - We use Em for amplitude.
- Peak-to-peak voltage is measured between the

minimum and maximum peaks. - We use Ep-p or Vp-p.

Peak Value

- The peak value of a voltage or current is its

maximum value with respect to zero. - If a sine wave rides on top of a dc value, the

peak is the sum of the dc voltage and the ac

waveform amplitude.

(No Transcript)

The Basic Sine Wave Equation

- The voltage produced by a generator is
- e Emsin ?.
- Em is the maximum voltage and ? is the

instantaneous angular position of the rotating

coil of the generator. - The voltage at any point on the sine wave may be

found by multiplying Em times the sine of angle

at that point.

Angular Velocity

- The rate at which the generator coil rotates is

called its angular velocity, ?. - The units for ? are revolutions/second,

degrees/sec, or radians/sec.

Radian Measure

- ? is usually expressed in radians.
- 2? radians 360
- To convert from degrees to radians, multiply by

?/180. - To convert from radians to degrees, multiply by

180/?.

Relationship between ?,T, and f

- One cycle of a sine wave may be represented by ?

2? rads or t T s.

Voltages and Currents as Functions of Time

- Since ?? ?t, the equation e Emsin ? becomes e

Emsin ?t. - Also v Vmsin ?t and i Imsin ?t.
- These equations may be used to compute voltages

and currents at any instant of time.

Voltages and Currents with Phase Shifts

- If a sine wave does not pass through zero at
- t 0, it has a phase shift.
- For a waveform shifted left,
- v Vmsin(?t ?).
- For a waveform shifted right,
- v Vmsin(?t - ?).

Phase shifts

Phasors

- A phasor is a rotating line whose projection on a

vertical axis can be used to represent

sinusoidally varying quantities. - A sinusoidal waveform can be created by plotting

the vertical projection of a phasor that rotates

in the counterclockwise direction at a constant

angular velocity ?. - Phasors apply only to sinusoidal waveforms.

Rotating phasor

Shifted Sine Waves

- Phasors may be used to represent shifted

waveforms. - The angle ? is the position of the phasor at t

0 seconds.

Phase Difference

- Phase difference is the angular displacement

between waveforms at the same frequency. - If the angular displacement is 0, the waveforms

are in phase otherwise they are out of phase. - If v1 5 sin(100t) and v2 3 sin(100t - 30),

v1 leads v2 by 30.

Phase differences

Average Value

- To find an average value of a waveform, divide

the area under the waveform by the length of its

base. - Areas above the axis are positive, areas below

the axis are negative. - Average values are also called dc values because

dc meters indicate average values rather than

instantaneous values.

Sine Wave Averages

- The average value of a sine wave over a complete

cycle is zero. - The average over a half cycle is not zero.
- The full-wave average is 2/?0.637 times the

maximum value. - The half-wave average is 1/? 0.318 times the

maximum value.

Effective Values

- An effective value is an equivalent dc value.
- It tells how many volts or amps of dc that an ac

waveform is equal to in terms of its ability to

produce the same average power. - In Australia, house voltage is 240 V(ac). This

means that the voltage is capable of producing

the same average power as 240 V(dc).

Effective Values

- To determine the effective power, we set

Power(dc) Power(ac). - Pdc pac
- I2R i2R where i Imsin ?t
- By applying a trigonometric identity, we are able

to solve for I in terms of Im. - Ieff Im/ ?2 0.707Im
- Veff 0.707Vm
- The effective value is also known as the RMS

value.

- R,L, and C Elements and the Impedance Concept

Introduction

- To analyze ac circuits in the time domain is not

very practical. - It is more practical to represent voltages and

currents as phasors, circuit elements as

impedances, and use complex algebra to analyze. - With this approach, ac circuits can be handled

much like dc circuits - the relationships and

laws still apply.

Complex Number Review

- A complex number is in the form a jb, where j

- a is the real part and b is the imaginary part of

the complex number. - This called the rectangular form.
- A complex number may be represented graphically

with a being the horizontal component and b being

the vertical component.

Conversion between Rectangular and Polar Forms

- If C a jb in rectangular form, then C C??,

where

Complex Number Review

- j 2 -1
- j 3 -j
- j 4 1
- 1/j -j
- To add complex numbers, add the real parts and

imaginary parts separately. - Subtraction is done similarly.

Review of Complex Numbers

- To multiply or divide complex numbers, it is best

to convert to polar form first. - (A??)(B??) (AB)?(? ?)
- (A??)/(B??) (A/B)?(? - ?)
- (1/C??) (1/C)?-?
- The complex conjugate of a jb is a - jb.

Voltages and Currents as Complex Numbers

- AC voltages and currents can be represented as

phasors. - Since phasors have magnitude and angle, they can

be viewed as complex numbers. - A voltage given as 100 sin(314t 30) can be

written as 100?30.

Voltages and Currents as Complex Numbers

- We can represent a source by its phasor

equivalent from the start. - The phasor representation contains all the

information we need except for the angular

velocity. - By doing this, we have transformed from the time

domain to the phasor domain. - KVL and KCL apply in both time domain and phasor

domain.

Sinusoidal source complex number

Summing AC Voltages and Currents

- To add or subtract waveforms in time domain is

very tedious. - This can be done easier by converting to phasors

and adding as complex numbers. - Once the waveforms are added, the corresponding

time equation and companion waveform can be

determined.

Summing waveforms point by point

Summing phasors

Important Notes

- Until now, we have used peak values when writing

voltages and current in phasor form. It is more

common that they be written as RMS values. - To add or subtract sinusoidal voltages or

currents, convert to phasor form, add or

subtract, then convert back to sinusoidal form. - Quantities expressed as phasors are said to be in

phasor domain or frequency domain.

R,L, and C Circuits with Sinusoidal Excitation

- R, L, and C circuit elements each have quite

different electrical properties. - These differences result in different

voltage-current relationships. - When a circuit is connected to a sinusoidal

source, all currents and voltages in the circuit

will be sinusoidal. - These sine waves will have the same frequency as

the source and will differ from it only in terms

of their magnitudes and angles.

Resistance and Sinusoidal AC

- In a purely resistive circuit, Ohms Law applies

the current is proportional to the voltage. - Current variations follow voltage variations,

each reaching their peak values at the same time. - The voltage and current of a resistor are in

phase.

Resistance

- For a resistor, the voltage and current are in

phase. - If the voltage has a phase angle, the current has

the same angle. - The impedance of a resistor is equal to R?0.

Inductive Circuit

- The voltage of an inductor is proportional to the

rate of change of the current. - Because the voltage is greatest when the rate of

change (or the slope) of the current is greatest,

the voltage and current are not in phase. - The voltage phasor leads the current by 90 for

an inductor.

Inductive Reactance

- Inductive reactance, XL, represents the

opposition that inductance presents to current

for the sinusoidal ac case. - XL is frequency-dependent.
- XL V/I and has units of ohms.
- XL ?L 2?fL

Inductance

- For an inductor, voltage leads current by 90.
- If the voltage has an angle of 0, the current

has an angle of -90. - The impedance of an inductor is XL?90.

Inductance V and I

Inductance V and I

Capacitive Circuits

- In a capacitive circuit, the current is

proportional to the rate of change of the

voltage. - The current will be greatest when the rate of

change of the voltage is greatest, so the voltage

and current are out of phase. - For a capacitor, the current leads the voltage by

90.

Capacitive Reactance

- Capacitive reactance, XC, represents the

opposition that capacitance presents to current

for the sinusoidal case. - XC is frequency-dependent. As the frequency

increases, XC decreases. - XC V/I and has units of ohms.

Capacitance

- For a capacitor, the current leads the voltage by

90. - If the voltage has an angle of 0, the current

has an angle of 90. - The impedance of a capacitor is given as XC?-90.

Capacitance V and I

Impedance

- The opposition that a circuit element presents to

current is the impedance, Z. - Z V/I, is in units of ohms
- Z in phasor form is Z?? where ? is the phase

difference between the voltage and current.

Impedance

About PowerShow.com

PowerShow.com is a leading presentation/slideshow sharing website. Whether your application is business, how-to, education, medicine, school, church, sales, marketing, online training or just for fun, PowerShow.com is a great resource. And, best of all, most of its cool features are free and easy to use.

You can use PowerShow.com to find and download example online PowerPoint ppt presentations on just about any topic you can imagine so you can learn how to improve your own slides and presentations for free. Or use it to find and download high-quality how-to PowerPoint ppt presentations with illustrated or animated slides that will teach you how to do something new, also for free. Or use it to upload your own PowerPoint slides so you can share them with your teachers, class, students, bosses, employees, customers, potential investors or the world. Or use it to create really cool photo slideshows - with 2D and 3D transitions, animation, and your choice of music - that you can share with your Facebook friends or Google+ circles. That's all free as well!

For a small fee you can get the industry's best online privacy or publicly promote your presentations and slide shows with top rankings. But aside from that it's free. We'll even convert your presentations and slide shows into the universal Flash format with all their original multimedia glory, including animation, 2D and 3D transition effects, embedded music or other audio, or even video embedded in slides. All for free. Most of the presentations and slideshows on PowerShow.com are free to view, many are even free to download. (You can choose whether to allow people to download your original PowerPoint presentations and photo slideshows for a fee or free or not at all.) Check out PowerShow.com today - for FREE. There is truly something for everyone!

You can use PowerShow.com to find and download example online PowerPoint ppt presentations on just about any topic you can imagine so you can learn how to improve your own slides and presentations for free. Or use it to find and download high-quality how-to PowerPoint ppt presentations with illustrated or animated slides that will teach you how to do something new, also for free. Or use it to upload your own PowerPoint slides so you can share them with your teachers, class, students, bosses, employees, customers, potential investors or the world. Or use it to create really cool photo slideshows - with 2D and 3D transitions, animation, and your choice of music - that you can share with your Facebook friends or Google+ circles. That's all free as well!

For a small fee you can get the industry's best online privacy or publicly promote your presentations and slide shows with top rankings. But aside from that it's free. We'll even convert your presentations and slide shows into the universal Flash format with all their original multimedia glory, including animation, 2D and 3D transition effects, embedded music or other audio, or even video embedded in slides. All for free. Most of the presentations and slideshows on PowerShow.com are free to view, many are even free to download. (You can choose whether to allow people to download your original PowerPoint presentations and photo slideshows for a fee or free or not at all.) Check out PowerShow.com today - for FREE. There is truly something for everyone!

presentations for free. Or use it to find and download high-quality how-to PowerPoint ppt presentations with illustrated or animated slides that will teach you how to do something new, also for free. Or use it to upload your own PowerPoint slides so you can share them with your teachers, class, students, bosses, employees, customers, potential investors or the world. Or use it to create really cool photo slideshows - with 2D and 3D transitions, animation, and your choice of music - that you can share with your Facebook friends or Google+ circles. That's all free as well!

For a small fee you can get the industry's best online privacy or publicly promote your presentations and slide shows with top rankings. But aside from that it's free. We'll even convert your presentations and slide shows into the universal Flash format with all their original multimedia glory, including animation, 2D and 3D transition effects, embedded music or other audio, or even video embedded in slides. All for free. Most of the presentations and slideshows on PowerShow.com are free to view, many are even free to download. (You can choose whether to allow people to download your original PowerPoint presentations and photo slideshows for a fee or free or not at all.) Check out PowerShow.com today - for FREE. There is truly something for everyone!

For a small fee you can get the industry's best online privacy or publicly promote your presentations and slide shows with top rankings. But aside from that it's free. We'll even convert your presentations and slide shows into the universal Flash format with all their original multimedia glory, including animation, 2D and 3D transition effects, embedded music or other audio, or even video embedded in slides. All for free. Most of the presentations and slideshows on PowerShow.com are free to view, many are even free to download. (You can choose whether to allow people to download your original PowerPoint presentations and photo slideshows for a fee or free or not at all.) Check out PowerShow.com today - for FREE. There is truly something for everyone!

Recommended

«

/ »

Page of

«

/ »

Promoted Presentations

Related Presentations

Page of

Home About Us Terms and Conditions Privacy Policy Presentation Removal Request Contact Us Send Us Feedback

Copyright 2018 CrystalGraphics, Inc. — All rights Reserved. PowerShow.com is a trademark of CrystalGraphics, Inc.

Copyright 2018 CrystalGraphics, Inc. — All rights Reserved. PowerShow.com is a trademark of CrystalGraphics, Inc.

The PowerPoint PPT presentation: "AC Fundamentals" is the property of its rightful owner.

Do you have PowerPoint slides to share? If so, share your PPT presentation slides online with PowerShow.com. It's FREE!