PowerPointpresentatie

1
Welcome
Legamaster Interactive media
eBeam System 3 Setup USB
Setup Guide
2
eBeam System 3
featuring Capture Software
Together eBeam system 3 with eBeam Capture
software records all of your handwritten notes
and drawings and saves them back to your computer
so they can be edited, printed, e-mailed, and
shared with anyone, anywhere in the world.
3
Whats in the Box?
USB eBeam Receiver with attachment brackets
Software CD, manual and cable
Eraser
10 Batteries (not shown)
4 Color-coded marker sleeves 4 Legamaster e-Board
markers
Shortcut Strip
4
eBeam Positioning Technology
The marker sleeves and eraser are powered by
standard alkaline batteries which are available
at any local store. Expected battery life is
approximately 60-80 hours of continuous writing.
DSP Proprietary and patented filtering code
eliminates interference from outside sources.
Complex algorithms run continuously in the
on-board DSP. Proprietary and patented filtering
code eliminates interference from outside sources.
eBeam positioning technology works in a similar
way to lightning in a thunderstorm by computing
the time difference between the speed of light
and the speed of sound.
5
Marker Sleeve Setup
6
Marker Sleeve Setup
Place a dry-erase marker into the appropriately
colored sleeve.
Gently twist the battery cap counterclockwise
until it releases. Place two batteries into each
of the marker sleeves (positive side up).
Place one of the black caps on the tip of the
marker. This will form an airtight seal so the
ink wont dry out.
7
Eraser Setup
8
Eraser Setup
Using a coin, twist the electronic erasers
battery cap counterclockwise until it
releases. Insert two batteries positive side up
and replace the cap carefully.
Fit coin into eraser cap groove.
Rotate coin counterclockwise
9
Connecting the System
e-Clip
Whiteboard
e-Board
10
Connecting the System
Whiteboard
Plug the small end of the USB cable into the
eBeam receiver.
Place the receiver in any of the four corners of
the board at a 90 angle. We recommend placing
the eBeam in one of the top corners. This will
reduce the chance of blocking the sleeves signal
with your hand.
Plug the larger end of the USB cable into the
computer.
11
Connecting the System
e-Clip Flipchart
Plug the small end of the USB cable into the
eBeam receiver.
Place the eBeam receiver on the e-Clip and screw
the e-Clip onto the flipchart.
Plug the larger end of the USB cable into the
computer.
With the special functionkey strip, you can
printdirectly or go to a new page.
12
Connecting the System
e-Board
Plug the small end of the USB cable into the
e-Board receiver.
Plug the larger end of the USB cable into the
computer.
13
Installing eBeam Capture Software
14
Installing eBeam Capture Software
Load the eBeam software onto your computer from
the CD or from our website at www.legamaster.com
If you choose to Launch the Software from the
installation wizard, an eBeam Capture window will
automatically open.
If you choose not to launch it immediately you
can open the software by using the eBeam shortcut
on your desktop.
15
Calibrating the System
16
Calibrating the System
Once the software is loaded, you can then
calibrate your eBeam. In the Capture window, go
to Tools gt Calibrate Capture Area
17
Calibrating the System
Using your mouse, select which corner of the
whiteboard your eBeam receiver is in and
click Next gt
18
Calibrating the System
The calibration wizard will ask you to click a
specific corner of the board. Using one of the
marker sleeves, tap the highlighted corner on
your physical whiteboard.
19
Calibrating the System
Once the first tap has been registered, the
wizard will request the opposite corner. After
the second tap is accepted, anything you write
within that designated area will be captured back
to your computer.
20
Calibrating the Shortcut Strip
21
Calibrating the Shortcut Strip
Peel the paper backing off the strip and place it
within the calibrated portion of your whiteboard.
In the Capture window, go to Tools gt Shortcut
Strip gt Calibrate
The Shortcut Strip gives you a quick way to
start a new page or to print the current page
straight from the board.
22
Calibrating the Shortcut Strip
Tap here on your physical whiteboard.
The Shortcut Strip wizard will open and ask you
to tap the upper left-hand corner of the strip.
Follow these instructions using one of the marker
sleeves on your physical whiteboard.
23
Tap here on your physical whiteboard.
When the first point has been registered, the
wizard will ask you to click the bottom
right-hand corner. After it accepts this point,
your Shortcut Strip is ready to be used.
24
Welcome
Legamaster Interactive media
Thank you for your attention!