English - DIGIPLEXNE-EM

1
Manual de utilizare pentru
2
Tastatura LCD si Tastatura LCD pentru acces
control DGP2-641 and DGP2-641AC
3
LCD Keypad and Access Control LCD Keypad DGP2-641
and DGP2-641AC
4
Armare regulata
Armarea regulat armeaza toate zonele din aria
selectata(e)
5
Armarea fortata- Force Arming
Armarea fortata permite armare sistemului cu zone
deschise. Zonele se programeaza in prealabil
6
Armarea partiala Stay Arming
Stay arming va arma partial sistemul, - doar
zonele nedeclarate stay (progrmarea se face in
prealabil de programator la cerere)
7
Armarea Instant
Cu armarea instant,toate zonele vor genera alarma
imediat ce se armeaza sistemul(chiar si zonele
definite intarziat)
8
Disarming
To disarm when entering

1. Select the desired area(s).

1. Select the desired area(s).

9
Bypass Programming
When a zone is bypassed, it will be ignored the
next time your system is armed.

1. Press the BYP button once the desired zone
   appears on the screen.

1. Repeat steps 3 and 4 until all desired zones
   selected.

10
Programare Chime
Tastatura poate fi programatasa emita un
sunet(beep) rapid si intermitent de fiecare data
cand zona programta este deschisa.

1. Tasteaza butonul 1 pentru a seta zona(ele)
   chime .

1. Introdu numarul zonei(din 2 digiti).

11
Programming a Chime Zone Schedule
Chime zones can also be programmed to chime only
when opened between certain hours.

1. Press the 2 button to set a chime schedule.

1. Enter a start time according to the 24hr clock
   (900 p.m. 2100).

1. Enter an end time according to the 24hr click
   (900 p.m. 2100).

12
Alarm Memory Display
13
One-Touch Buttons
Press and hold the desired one-touch button to
access the following
14
Panic Buttons
Press and hold one of the button combinations
listed below to send a panic alarm.
15
Programming User Access Codes Steps 1 to 6

1. Enter the 3-digit User Number to program.

1. Enter a user code (PIN)

16
Programming User Access Codes Steps 7 to 9

1. Enter the number of the area you wish to assign.

17
Programming User Access Codes Steps 10 and 11

1. Enter 2-digit access level.

1. Enter 2-digit schedule.

18
Programming User Access Codes Steps 12 to 15

1. Press the ? button.

1. Enter the access control cards serial number by
   either using the keypads buttons or by
   presenting the card to the keypads reader.

1. Press ENTER to save and exit.

19
Trouble Display
20
Trouble Display Group 1 System
Group 1 System
AC Failure
Battery Trouble
AUX Current Limit
Bell Current Limit
Bell Absent
ROM Check Error
RAM Check Error (DGP-NE96)
21
Trouble Display - Group 2 Communicator
Group 2 Communicator
TLM1
Fail to Communicate 1
Fail to Communicate 2
Fail to Communicate 3
Fail to Communicate 4
Fail to Communicate PC
22
Trouble Display - Group 3 Modules
Group 3 Modules
Module Tamper
ROM Check Error
TLM Trouble
Fail to Communicate
Printer Trouble
AC Failure
Battery Failure
Supply Output
23
Trouble Display - Groups 4 to 8
Group 4 Bus
Missing Keypad
Missing Module
General Failure
Bus Overload
Bus Comm. Error
Group 5 Zone Tamper
Group 6 Zone Low Battery
Group 7 Zone Fault
Group 8 Clock Loss
24
Thank You