CFD ANALYSIS OF CROSS FLOW AIR TO AIR - PowerPoint PPT Presentation

1 / 24
About This Presentation
Title:

CFD ANALYSIS OF CROSS FLOW AIR TO AIR

Description:

4 Crompton Greaves Ltd, Kanjur Marg, Mumbai, India. PHOENICS USER CONFERENCE 2004 ... M/S Crompton Greaves, Mumbai, India for providing the funds in addition to ... – PowerPoint PPT presentation

Number of Views:225
Avg rating:3.0/5.0
Slides: 25
Provided by: CDAC4
Category:
Tags: air | analysis | cfd | cross | flow | greaves

less

Transcript and Presenter's Notes

Title: CFD ANALYSIS OF CROSS FLOW AIR TO AIR


1
  • CFD ANALYSIS OF CROSS FLOW AIR TO AIR
  • TUBE TYPE HEAT EXCHANGER
  •  
  • Vikas Kumar1, D. Gangacharyulu2,
  • Parlapalli MS Rao3 and R. S. Barve4
  • 1 Centre for Development of Advanced Computing,
    Pune University Campus, Pune, India
  • 2 Thapar Institute of Engineering Technology,
    Patiala, India
  • 3 Nanyang Technological University, Singapore
  • 4 Crompton Greaves Ltd, Kanjur Marg, Mumbai,
    India

2
Introduction
  • Closed Air Circuit Air Cooled (CACA) electrical
    motors are used in various industries for higher
    rating (500 kW and above) applications
  • Heat generation due to the energy losses in the
    windings of motors at various electrical loads
    under operating condition
  • Cold air is circulated in the motor to remove the
    heat generated
  • The hot air generated in the motor is cooled by
    using an air to air tube type cross flow heat
    exchangers
  • The motor designers are interested to know the
    temperature distribution of air in the heat
    exchanger and pressure drop across the tube
    bundle at various operating parameters, e.g.,
    different hot cold air temperatures and fluid
    (hot cold) flow rates

3
Large Electrical Motor
Heat exchanger
Source M/S Crompton Greaves Ltd. Mumbai, India
4
Heat Exchanger Geometry
External hot air
cooled air
Internal hot air
External cold air
cooled air
5
OBJECTIVE
  •  
  • Predictions of
  • Pressure
  • Air flow and
  • Temperature distributions
  • in the heat exchangers

6
Heat Exchanger Geometry
7
Table 1 Geometrical details of the heat
exchanger
Sl. No. Description Unit Value/Type
1. Overall dimension mm  1760 x 100 x 765
2. Tube inner diameter mm 22
3. Tube outer diameter mm 26
4. Tube length mm 1610
5. No. of tubes - 27
6. Transverse pitch mm 61
7. Longitudinal pitch mm 41
8
  • Modeling Considerations
  • Geometry has symmetry in width wise.
  • A section of heat exchanger consisting of 9 rows
    3 columns has been considered for analysis.
    Each column has 9 tubes.
  • Tube is modeled as solid blockage, whereas, the
    inner volume of the tube has been modeled as
    blockage with gaseous properties to allow the
    ambient air to pass through it by using PHOENICS
    CFD Software.
  • Conduction takes place from the tube wall
    convection takes place from the surface of the
    tube.
  • The partition plate and baffle participate in
    heat transfer.
  • Temperature flow distributions have been
    considered to be three dimensional in nature.
  • k-e turbulence model has been considered.
  • Hybrid difference scheme has been used.

9
Grid generation for heat exchanger
The distribution of cells in the three directions
are given below X Direction 55 Y
Direction 48 Z Direction 232 The
total number of cells in the computational domain
is 612,480.
10
Fig. 3 Side view of the grid
11
Table 2 Operating boundary conditions of the
heat exchanger
Sl. No. Input parameters Unit Value
1. Temperature of cold air oC 35
2. Temperature of hot air oC 63
3. Volumetric flow rate of cold air cfm (cu.m/m) 388 (10.98)
4. Volumetric flow rate of hot air cfm (cu.m/m) 228.80 (6.48)
12
Results Discussions
  • The highest pressure region has been observed
    nearby the top of the separating plate, which may
    be due to the large change in the momentum of the
    cold fluid caused by the plate.
  • Hot fluid recirculation has been observed at the
    top corner of 1st 4th section.
  • The temperature drop of the hot air in the 1st
    section of the heat exchanger is higher than 4th
    section because of the high temperature
    difference between the cold air and the hot air.

13
Fig. 4 Pressure distribution in the heat
exchanger
14
Fig. 5 Velocity distribution in the heat
exchanger
15
Fig. 6 Temperature distribution in the heat
exchanger
16
Fig. 7 Temperature distribution in the tube
bundle of the heat exchanger
17
Table 3 Comparison of air temperature prediction
at various outlets
Sl. No.   Inlet temperature, oC Inlet temperature, oC Inlet temperature, oC Outlet temperature, oC Outlet temperature, oC Outlet temperature, oC Remarks
Sl. No.   Cold air Hot air 2nd section Hot air 3rd section Hot air 1st section Hot air 4th section Cold air Remarks
1. 34.4 63 63 41.9 51.8 46.8 Experimental
2. 34.4 63 63 44.70 49.55 43.68 PHOENICS Simulation
3. 34.4 61 65 43.68 50.9 44.32 PHOENICS Simulation
18
Fig. 8 A comparison between the results of CFD
simulation experiments
19
Fig. 9 Temperature distribution in the heat
exchanger a case study
20
Fig. 10 Temperature distribution of the heat
exchanger (after modification of central
partition plate)
21
(Sun Ultra SPARC-450, 300 MHz)
Fig. 11 Effect of number of processors in
computing time using parallel PHOENICS
22
Conclusions
  • A method for predicting the pressure, velocity
    temperature distributions in the tube type heat
    exchanger associated with CACA large motor has
    been developed using PHOENICS CFD software.
  • The simulated results predict the temperature
    distribution reasonably at different locations of
    the heat exchanger.
  • The CFD model may be used to optimize its thermal
    performance by varying the location of the
    baffles the partition plate in the heat
    exchanger and in turn to improve the performance
    of electrical motors.
  • The parallel PHOENICS can be used to reduce the
    design cycle of the equipment due to fast
    computation.

23
Acknowledgements
  • M/S Thapar Centre for Industrial Research
    Development, Patiala, India for providing the
    necessary facilities to carry out this project
  • M/S Crompton Greaves, Mumbai, India for providing
    the funds in addition to drawing, design data and
    experimental results
  • M/S CHAM, U.K (support team) for technical help
  • M/S Centre for Development of Advanced Computing
    (C-DAC), Pune, India for providing the
    facility to use PARAM 10000 for running parallel
    PHOENICS and funding for presenting this paper

24
THANK YOU
Write a Comment
User Comments (0)
About PowerShow.com