ECET 340 Squared Instruction Uophelp

1
ECET 340 Course Tutorial

• For more course tutorials visit
• www.uophelp.com

2
ECET 340 Entire Course (All ilabs and Homework)
(Devry)

• For more course tutorials visit
• www.uophelp.com
• ECET 340 Week 1 HomeWork 1
• ECET 340 Week 1 iLab 1
• ECET 340 Week 2 HomeWork 2
• ECET 340 Week 2 iLab 2
• ECET 340 Week 3 HomeWork 3
• ECET 340 Week 3 iLab 3
• ECET 340 Week 4 HomeWork 4
• ECET 340 Week 4 iLab 4

3
ECET 340 Week 1 HomeWork 1 (Devry)

• For more course tutorials visit
• www.uophelp.com
• 1. Give three examples each of internal and extern
  al peripheral devices as referenced to the HCS12
  microcontroller and not an entire PC. (2
  points)2. Given the requirements of each
  signals destination must match the capabilities
  of the signals source, name some of the
  electrical signal parameters that must be
  considered when designing an interface between
  two different hardware components. (2 points)

4
ECET 340 Week 1 iLab 1 (Devry)

• For more course tutorials visit
• www.uophelp.com
• To become familiar with Microcontroller MC9S12
  parallel ports and how simple input and output
  devices are interfaced through them.
• To learn how to program I/O instructions in C
  language.
• To learn how to organize a program to read data
  from input ports, process the data, and display
  the result on a simple output device.

5
ECET 340 Week 2 HomeWork 2 (Devry)

• For more course tutorials visit
• www.uophelp.com
• . Where does program control transfer to when an
  interrupt occurs? 2 points
• 2. Which one of the following Interrupts has
  highest priority? 2 points
• 3. RAM Vector table addresses 3E52 belongs to
  which interrupt? 2 points
• 4. Before exiting an ISR, the programmer should
  use which command? 2 points

6
ECET 340 Week 2 iLab 2 (Devry)

• For more course tutorials visit
• www.uophelp.com
• ECET 340 Week 2 iLab 2 (Devry)

7
ECET 340 Week 3 HomeWork 3 (Devry)

• For more course tutorials visit
• www.uophelp.com
• 1. Sketch a circuit that can be used to debounce
  a pushbutton and explain how it works. (4 points
  max)
• 2. In Figure 7.32 on page 339 of the Huang
  textbook, if the row has and the columnsare ,
  which key is pressed? (2 points max)
• 3. In Figure 7.32 on page 339 of the Huang
  textbook, explain why the 10k? resistors ties to
  VCC are required. (2 points max)

8
ECET 340 Week 3 iLab 3 (Devry)

• For more course tutorials visit
• www.uophelp.com
• SOLVED ECET 340 iLAB3
• OBJECTIVES
• To learn the basic operation of a keypad.
• To understand how to interface a keypad to a
  microprocessor.
• To learn how to program a keypad driver in C
  language.

9
ECET 340 Week 4 HomeWork 4 (Devry)

• For more course tutorials visit
• www.uophelp.com
• 1. Determine the conversion time for an ADC0804
  (8-bit), where 66 clocks per bit are required, if
  its clock frequency is 50 kHz.2. If an 8-bit
  SAR has Vref 10 V, what is the binary value for
  an input voltage of 7.28 V?3. What is the
  percent error for the binary answer found in
  Problem 2?4. Given an 24 MHz bus speed. Write
  down the line(s) of instruction which set the
  ATD1 unit for 2MHz conversion frequency, 10-bit
  resolution and 8 A-to-D clocks per sample time.

10
ECET 340 Week 4 iLab 4 (Devry)

• For more course tutorials visit
• www.uophelp.com
• To learn how to use A-to-D converters to digitize
  signals from analog input devices.
• To learn how to write a C language program that
  samples the data from an analog device, digitizes
  it and formats it for output on an LCD.
• To become more proficient in programming displays
  for real-time operation

11
ECET 340 Week 5 HomeWork 5 (Devry)

• For more course tutorials visit
• www.uophelp.com
• . Explain, briefly, why an analog restoring
  filter is sometimes used at the output of a
  DAC.2. Given Iref 2 mA for a DAC1408 IC, find
  Iout for the input 1110 11103. Find the number
  of discrete voltages output by a 12-bit DAC. Show
  work.4. Use the internet to locate the data
  sheet for an MC1408 DAC. From it find, for the
  MC1408-7 version, the following

12
ECET 340 Week 5 iLab 5 (Devry)

• For more course tutorials visit
• www.uophelp.com
• Scenario/Summary
• This week's lab covers two areas, conversion of
  digital HCS12 
• signals to an analog format, and the use of a
  Serial Peripheral Interface (SPI) 
• to transfer data, and commands between the HCS12,
  and the DAC 
• peripheral. 

13
ECET 340 Week 6 HomeWork 6 (Devry)

• For more course tutorials visit
• www.uophelp.com
• 1. What are the four main functions of the HC12
  Timer unit?2. Two input capture events occur at
  counts 0x1037 and 0xFF20 of the free-running
  counter. How many counts (in decimal) have
  transpired between these two events?

14
ECET 340 Week 5 DQ 2

• For more course tutorials visit
• www.uophelp.com
• Based on the Yew (2009) article, how does the
  information presented to decision makers affect
  the quality of their decisions?

15
ECET 340 Week 6 iLab 6 (Devry)

• For more course tutorials visit
• www.uophelp.com
• ECET 340 Week 6 iLab 6 (Devry)

16
ECET 340 Week 7 HomeWork 7

• For more course tutorials visit
• www.uophelp.com
• 1. The movable part of the solenoid is the 2
  points
• 2. Why is the 6N139 optoisolator used in the
  interfaces to devices such as large motors? 2
  points
• 3. Calculate the number of steps per revolution
  for a stepper motor with a step angle of 7.5. 2
  points
• 4. How is stepper motor speed controlled? State
  any two ways a program can do this. 2 points

17
ECET 340 Course Tutorial

• For more course tutorials visit
• www.uophelp.com